RUFFO
05-abr-2010, 12:08
Tutorial Dongle cw 700 , 800
CW 700sv2.45_2009_12_29 Dongle
This file is just for Dongle, if no Dongle, Please Do Not Use
No EMU in this file
Do Factory Default
Load the file
Scan sats
Config your receiver options
Exit to main screen, wait 5 secs (approx) for software to read the dongle
(NO MESS IN TV)
INFO + 0 = Server Status Display
INFO + 1 = Your Private Server Info (up to 40)
INFO + 2 = Your IP Status
No Dongle, No Menus
No Public Server available as of yet.
Attached Files
Este es para el 800
CW 800s Dongle Files
--------------------------------------------------------------------------------
CW 800sv2.45_2009_12_29 Dongle
This file is just for Dongle, if no Dongle, Please Do Not Use
No EMU in this file
Do Factory Default
Load the file
Scan sats
Configure your receiver options
Exit to main screen, wait 5 secs (approx) for software to read the dongle
(NO MESS IN TV)
INFO + 0 = Server Status Display
INFO + 1 = Your Private Server Info (up to 40)
INFO + 2 = Your IP Status
No Dongle, No Menus
No Public Server available as of yet.
Attached Files CW800SV2.45_2009_12_29.zip
Download and Unzip latest bin file.
Transfer unzipped file onto USB stick then plug it into the box. You should see a message that says USB ready. Now press the USB button on remote and then scroll to the right to open the Software tab. Look for new file and press OK to load it. After it loads, it will ask you if you want to reboot, say YES.
When it reboots then go in menu and do a Factory Default. Then reboot again from the rear power switch. When it comes back up again, now you can setup satellites and options and rescan all satellites. After that is done, exit out of all menus and with the remote press F1 000 to enable the Patch. You should see a message on your tv that will say PATCH ENABLED. Now wait for keys to roll and watch tv.
Cable Instructions
To Prepare Receiver:
Turn off and attach the null-modem cable between the receiver and the computer serial port.Then plug in the power plug.
With the CaptiveWorks 700 receiver off, press the front power button and hold it.
While holding it, turn the rear toggle switch on, while STILL holding front power button.
You will see "boot" on the front display.
1. Download the current loader - New CW-700S Upgrade Loader and unzip
2. Download the latest bin and unzip this file
3. Load the latest bin with the current loader as per these instructions:
Open the loader, select the latest bin in the "File" bar across the top.
For Options, select Download S/W.
To select a port, choose your COM port (usually 1). Then hit the start/load and wait for the receiver to display "-end". At this point, turn receiver OFF from the rear switch to reboot.You can now follow the last paragraph in the above USB instructions to help setup satellites and scan channels.
CW 700sv2.45_2009_12_29 Dongle
This file is just for Dongle, if no Dongle, Please Do Not Use
No EMU in this file
Do Factory Default
Load the file
Scan sats
Config your receiver options
Exit to main screen, wait 5 secs (approx) for software to read the dongle
(NO MESS IN TV)
INFO + 0 = Server Status Display
INFO + 1 = Your Private Server Info (up to 40)
INFO + 2 = Your IP Status
No Dongle, No Menus
No Public Server available as of yet.
Attached Files
Este es para el 800
CW 800s Dongle Files
--------------------------------------------------------------------------------
CW 800sv2.45_2009_12_29 Dongle
This file is just for Dongle, if no Dongle, Please Do Not Use
No EMU in this file
Do Factory Default
Load the file
Scan sats
Configure your receiver options
Exit to main screen, wait 5 secs (approx) for software to read the dongle
(NO MESS IN TV)
INFO + 0 = Server Status Display
INFO + 1 = Your Private Server Info (up to 40)
INFO + 2 = Your IP Status
No Dongle, No Menus
No Public Server available as of yet.
Attached Files CW800SV2.45_2009_12_29.zip
Download and Unzip latest bin file.
Transfer unzipped file onto USB stick then plug it into the box. You should see a message that says USB ready. Now press the USB button on remote and then scroll to the right to open the Software tab. Look for new file and press OK to load it. After it loads, it will ask you if you want to reboot, say YES.
When it reboots then go in menu and do a Factory Default. Then reboot again from the rear power switch. When it comes back up again, now you can setup satellites and options and rescan all satellites. After that is done, exit out of all menus and with the remote press F1 000 to enable the Patch. You should see a message on your tv that will say PATCH ENABLED. Now wait for keys to roll and watch tv.
Cable Instructions
To Prepare Receiver:
Turn off and attach the null-modem cable between the receiver and the computer serial port.Then plug in the power plug.
With the CaptiveWorks 700 receiver off, press the front power button and hold it.
While holding it, turn the rear toggle switch on, while STILL holding front power button.
You will see "boot" on the front display.
1. Download the current loader - New CW-700S Upgrade Loader and unzip
2. Download the latest bin and unzip this file
3. Load the latest bin with the current loader as per these instructions:
Open the loader, select the latest bin in the "File" bar across the top.
For Options, select Download S/W.
To select a port, choose your COM port (usually 1). Then hit the start/load and wait for the receiver to display "-end". At this point, turn receiver OFF from the rear switch to reboot.You can now follow the last paragraph in the above USB instructions to help setup satellites and scan channels.